ArtNet SPI Controller MR-A28A for LED Pixel Lighting

Artnet-SPI-Controler-for-LED-Pixel-Light-MR-A28A-Lineart-Lighting-1

ArtNet SPI Controller MR-A28A for LED Pixel Lighting Description:

MR-A28A control system supports signal communication and transmission by ArtNet protocol of Ethernet; The hardware integrated with software sends multi-channel data to led pixel lighting with SPI(Serial Peripheral Interface ) in the form of TTL protocol.

The MR-A28A control system adopts high-performance FPGA processor. It processs data high efficiently and stably. This controller has two RJ45 network interfaces, compatible with conventional network devices in various topological structure.

Compatible Softwares:

MR-A28A provides 8 standard TTL data output ports, which output a total of 8×512 chanenls and support extended protocol. The light control software is compatible with ArtNet protocol such as: Madrx3, Madrx5, Programmer, Pharos, Sunlite, Luminair, Arocos, MA console, and so on;

Applicatons:

This ArtNet SPI controller regularly apply in LED pixel lighting like light matrix and stage lighting control systems which require a large amount of TTL channel data. You will use them in TV stations, stage performances, night bars, light shows, immersive performances, 3D mapping shows and other building facades.

FEATURES

1. MR-A28A Supports ArtNet Protocol and is Based on TCP/IP Ethernet Protocol;The Distance is 100 Meters

2. MR-A28A Outputs TTL Level Signals (2 Channels) and Differential Signals (1 Channel);

3. MR-A28A Device Supports Cascade Transmission of 254 Devices；

4. MR-A28A Supports 64 Universer and a Single Port Can be Expanded by 8 Times, That is, 4096 Channels (Depending on Chip Performance)；

5. The User Can Set up Two Different IP Addresses；

6. Support 32-65536 Grayscale 16Bit, Support 262144 Grayscale, Restore image Details;

7. Independent Brightness Control of 3 Primary Colors, Easy to Adjust White Balance;

8. Support R,RB,RGB,RGBW,RGBWY, and Multi-Color Mixing Control;

9. Accurate Gamma Correction Algorithm, in Line With Human Visual Sense;

10. Support 120Hz Frame Rate to Ensure High-definition Display and 3D Requirements;

11. Using Ethernet Interface and TCP/IP Protocol, The Distance is 100 Meters;

12. The LCD Display Module Displays the Controller Parameters and Status in Time；

13. Support The Device ID Number Data Flow Sequence and Fixed Arrangement

FEATURES

14. Two RJ45 Ports, Support Mixed Cascading; Automatic Software Display Status;

15. A Variety of Chip Control is Integrated, and we Change the Control Chip Type,
Clock Frequency, Duty Cycle, Gray Scale Level and Other Parameters Through Software Setting；

16. Support IP Grouping Function, use Switch Parallel Scheme；

17. 8-Port Output, Unlimited Number of Single-Port Load Points, Self-test;

18. Support Dual backup, a Controller is Broken or a Disconnected Display is Not Affected；

19. Support Device Port Anti-interference and Leakage Design;

20. Support Overcurrent and Overvoltage Protection, Can run for a Long Time;

21. Equipment Network Port, Port OutPut, Surge Protection: 1.5KV;

22. Support Severe Working Environment -40℃-80℃, Normal Operation Without Failure;

23. Network Adaptive or Mandatory 100M Can be Set to Support More Loading;

24. Different Network Segments Can be Set up to Avoid Mutual interference
With Multiple Sets of ArtNet Data in the Same Network ;

25. Support Online One-Key Upgrade of Device Firmware.

Installation Schematic:

I. Console Mode (Connected to the MA Light Console)

MR-A28A ArtNet Device is Connect to MA Light Console Network Port

ArtNet SPI controller MA Light Console Lineart Lighting

II. Computer Mode (Connected to the Computer)

MR-A28A ArtNet Device Connects to the Computer Network Port (Pre-install Supporting ArtNet Protocol Software)

Madrix 5 ArtNet SPI lighting controller Lineart Lighting

Datasheets

MR-A28A ArtNet Controller instuction V4.4

Order Codes: MR-A28A

Inquiry